Advance adapters location

Advance adapters location DEFAULT

Advance Adapters 713123 User Manual

background image

ADVANCE ADAPTERS INC.

P/N: 713123

P.O. Box 247, 4320 Aerotech Center Way
Paso Robles, CA 93447

PAGE 1 OF 2

Telephone: (800) 350-2223

Fax: (805) 238-4201

Page Rev. Date:

12-20-02

SPECIAL NOTE:

The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void

any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that
you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a service
manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships
and parts stores.

KIT CONSISTS OF:

No.

Qty

Part No.

Description

1.

2

713123-BLK

ADAPTER PLATE

2.

2

713123S

MOTOR MOUNT SPACER

3.

12

723704

3/8" LOCK WASHERS

4.

6

723720

H.H.C.S. 3/8"-16 x 3/4" LG. (Grade 5)

5.

6

723722

H.H.C.S. 3/8"-16 x 1-1/4" LG. (Grade 5)

6.

12

723735

3/8" FLAT WASHERS

7.

1

GM001

GM INSTRUCTION MANUAL

CHEVY V8 TO 4.3 V6 ADAPTER PLATE

INSTALLATION INSTRUCTIONS:

The GM V8 engine block and 4.3 V6 engine block are identical as to engine mounts, water pumps, and width. The only
variation for the engine mount area is that the V8 engine mounts are located approximately 4-3/8" further forward than
the V6 mount location. By using these adapter plates, you will be able to retain the original V6 rubber insulators and bolt
the new Chevy V8 engine into location. The V8 hole locations will provide for minor adjustments. These mounts are
primarily used on S10 engine conversions that are replacing the 4.3 V6 with the Chevy V8.

NOTE:
We have found some stock 4.3 mounts will need to be ground
at the top of the mount for clearance on the Advance Adapters
steel plate.

Sours: https://www.manualsdir.com/manuals/550945/advance-adapters-713123.html

KIT CONSISTS OF:

No.QtyPart No.Description

ADVANCE ADAPTERS INC.P/N: 50-0406

P.O. Box 247, 4320 Aerotech Center WayNew Item: (03/99)

Paso Robles, CA 93447PAGE 1 OF 4

Telephone: (800) 350-2223Fax: (805) 238-4201Page Rev. Date: 07-10-06

SPECIAL NOTE:The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will

void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend

that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that

a service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at

automotive dealerships and parts stores.

1.151-8900CASTING (with sensor drilled) (Ref: 51-8900)

2.152-1500SPUD SHAFT WITH 10 SPLINES

3.1300619SENSOR

4.1715547TRANSFER CASE SHIFTER BRKT.

5.1716301BEARING

61*716345BEARING SLEEVE FOR CASTING (INSTALLED BY AA)

7.1716507GASKET

8.1716511"O"-RING

9.37237313/8"-16 x 1" S.H.C.S

10.272006312mm-1.25 x 40mm H.H.C.S.

11.572008512mm LOCK WASHER

12.372008912mm-1.25 x 130mm H.H.C.S.

13.1728701NYLON LOCK NUT 7/8"-16

14.17287027/8" FLATWASHER

15.1TLC001LAND CRUISER INSTRUCTION MANUAL

GM 4L60E AUTOMATIC OVERDRIVE

TO LAND CRUISERS 1963-73 FJ40 (3 SPEED)

NOTE: THIS KIT USES A 2WD 4L60E OUTPUT SHAFT (O.A.L. 18-3/16").

NOTE: This kit requires the 2WD output shaft to be shortened. If you are using this kit on a newer hex bolt

pattern 4L60E transmission, then you will be required to use our 51-0405 adapter housing. Please note that the

cut off location on the output shaft must be made after this adapter is installed on the transmission. This 51-0405

adapter make the hex pattern 4L60E transmission look just like the square bolt pattern transmission, and the cut

off location for the output shaft is shown on this instruction sheet is for the square bolt pattern transmission.

Sours: https://www.manualshelf.com/manual/advance-adapters/50-0406/user-guide-english.html
  1. Dmc size 3
  2. Mindustry oil
  3. Searay boat covers
  4. Machinima twitter
  5. November first meme

Advance Adapters 50-6308 User Manual

background image

GM TH350 AUTOMATIC TO

JEEP NP231 TRANSFER CASE-23 SPLINES

ADVANCE ADAPTERS INC.

P/N: 50-6308

P.O. Box 247, 4320 Aerotech Center Way

New Item: (11/93)

Paso Robles, CA 93447

PAGE 2 OF 3

Telephone: (800) 350-2223

Fax: (805) 238-4201

Page Rev. Date:

03-13-01

SPECIAL NOTE:

The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will

void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend

that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a

service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive

dealerships and parts stores.

GM TH350 3 SPEED AUTOMATIC

The General Motors TH350 has a case length of 21-1/2", 13 bolts holding the oil pan in position, and is available in two

different engine to transmission bolt patterns. The case is available with a Chevy bolt pattern that has the top two holes

8-1/4" apart, or a Buick bolt pattern that has the top two holes 7" apart. The rear side of the transmission case should have

a square bolt pattern that uses 4 bolts. There are several various lengths of output shafts that the transmissions have been

furnished with and you must make sure the proper shaft has been installed into the transmission for use with our transfer

case kit. We standardize our kits on the GM 4WD output shafts that were used in vehicles 1973-79. All TH350 output

shafts will have 27 splines. The speedometer gear is normally located in the tailhousing, but when adapting it to the transfer

case, the location will change to the backside of the transfer case. The rear transmission support is located in the main

case just forward of the tailhousing connection. This can be used for supporting the crossmember on some installations,

but most of our kits provide support on the new adapter housing.

When installing the new transfer case adapter, make sure that the coupler and the output shaft do not bottom out. We have

found on occasion that a transmission output shaft may be slightly longer than what we have allowed for; and when coupling

into our new spud shaft, we find a small amount of interference. The adapter housing and spud shaft must be assembled

to the back of the transmission without interference.

DO NOT FORCE THE NEW TAILHOUSING ONTO THE

TRANSMISSION.

If assistance is needed, please feel free to call the number listed above.

When assembling the adapter housing to the transmission case, we have provided you with a new square-type "O" ring

seal to prevent fluid leakage. This seal is a stock GM item that is used on all installations. We have also provided a gasket

for the Dana 300 to adapter surface. We also recommend a small amount of silicone be used on both surfaces. Loctite

should be used on all fasteners.

All installations will require the use of a transmission cooler. The cooler can be either installed in the radiator or a remote

location is acceptable. The transmission shift control can either be a Hurst floor mounted type shifter or sometimes the

existing column shift can be modified on certain applications.

INSTALLATION:

1. This kit comes pre-assembled with the bearing, snap rings, and spud shaft installed in the casting. The bearing and spud

shaft are a press fit. The spud shaft is pressed to the bearing and the snap ring installed to retain the spud shaft properly.

The bearing and spud shaft assembly are also a press fit into the adapter housing. The bearing and spud shaft are pressed

into the casting. This assembly is retained with the provided snap ring.

2. Install the o-ring on the casting and use a small amount of silicone to provide a good seal. Bolt the adapter assembly

to the TH350 transmission.

3. Using a thin film of silicone on both sides of the transfer case gasket, install the transfer case and gasket to the adapter

assembly. The studs in the Dana 300 should locate the transfer case in the proper rotation, and the Dana 300 front

alignment retainer should properly index the transfer case.

4. The Advance Adapters crossmember mount will bolt to the bottom of the adapter casting. Mark and drill new holes

in the skid plate to secure the transmission assembly to the skid plate.

5. Make sure all fasteners are secured and Loctite is used.

Sours: https://www.manualsdir.com/manuals/550733/advance-adapters-50-6308.html?page=2
Advance Adapters - \

The trousers burst right between her large buttocks. The hole went along the seam, it became clear how green thongs dig into her soft, defenseless white ass. The hole was getting bigger and bigger, but Aunt Natasha, apparently, did not feel anything - she continued to dance, more and more exposing her fifth point of support.

Small feet with fingers painted with turquoise lacquer spread like a cat on the floor, my chest jumped under the T-shirt, my hands made incredible and. Very beautiful passes, and a big already completely naked priest turned my head and I could not swallow and could not move.

Adapters location advance

Hey, wake up - I was pushed in the side by the. Librarian - this is not a shelter for you, I have to go home. She pulled a book out from under me and went into her closet. I am a sinner. Burn me in hell.

In Vehicle Install - Advance Adapters Slip Yoke Eliminator For NP231J - 2001 XJ

Slowly she pulled them off. Panties fell to the floor and I kicked them into the same chair. After thinking for a second, she went to the chair, took her linen and carried it to the bathroom, putting it.

You will also be interested:

Her panties and tights were all wet - this is for washing, Kira thought. Folding her school uniform neatly on a hanger, she put on a home jacket over her naked body and a home. Fly skirt. "Fashionista" thought Kira, mentally comparing them with Lera's panties.



1182 1183 1184 1185 1186